170 models · 61 series
266nm CW DUV Laser
5 models| Model | Wavelength | Output / average power | Pulse energy | Repetition rate | Pulse width | Power stability (rms, 4 hours , ±3℃) | Mode-locked all fiber pulsed laser at 266nm | M2 | Polarization ratio (dB) | Warm-up time (minutes) | Delivery fiber length(cm) | Cooled method | Operating temperature (℃) | Operating voltage (VDC) | Expected lifetime (hours) | Fundamental Frequency | Delivery fiber length (cm) | energy | Beam divergence, full angle (mrad) | Power supply (110/220VAC) | Ave power stability (rms, over 4 hours) | 1064/532/355/266nm Transverse mode | Cooling method | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Polarization ratio | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FL-266-PS | 266 nm | 1~10 mW | 0.02~0.5 nJ | 20-50 MHz | <10 ps | <5%, <3% | Pulse duration (ps) / <10 | <2 | >15 Horizontal (Vertical optional) | <15 | 60 | Air cooled | 15-35 | 12V/11.5A | >10000 | Forth harmonic | – | – | – | – | – | – | – | – | – | – | Datasheet |
| FL-266-Pico | 266 nm | 1~50 mW | 0.05~500 nJ | 100 kHz-20 MHz | 50-900 ps (fixed) | <5%, <3% | – | <2 | >15 Horizontal (Vertical optional) | <15 | – | Air cooled | 15-35 | 12V/11.5A | >10000 | Forth harmonic | 60 | – | – | – | – | – | – | – | – | – | Datasheet |
| DPS-266-Pico | 266 nm | 100~500 mW | 10~100 nJ | 5 MHz | <50 ps, 50-900 | <5%, <3% | – | – | – | <15 | – | Air cooled | 15-30 | – | >10000 | – | – | diode / pumped / all / solid | <3 | PSU-DPS-Pico | – | – | – | – | – | – | Datasheet |
| PS-D-266-Air | 266 nm | 1~100 mW | 1~12 uJ | 1 kHz-10 MHz | ~10 ps | – | – | <1.2 | – | ≥30 | – | – | – | 24V/20.9A | – | – | – | – | <3 | – | <3%,<2%, <1% | TEM00 | Air cooled | – | – | – | Datasheet |
| PS-D-266 | 266 nm | 1~5 W | 0.1~4 uJ | 400 kHz-1 MHz | ~10 ps | – | – | <1.2 / <1.3 | – | ≥30 | – | – | 20-30 | 36V/40A | >10000 | – | – | – | <2 | – | – | – | Water cooled | <3%, <2%, <1% | TEM00 | >100:1 Horizontal (Vertical optional) | Datasheet |
355nm CW Pulse UV Laser
9 models| Model | Wavelength | Output / average power | Pulse energy | Repetition rate | Pulse width | Power stability | M² | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Polarization ratio | Warm-up time (minutes) | Operating temperature (℃) | Operating voltage (VDC) | Expected lifetime (hours) | Power stability (rms, 4 hours , ±3℃) | Picosecond all fiber pulsed laser at 355nm | M2 | Polarization ratio (dB) | Delivery fiber length(cm) | Cooled method | Fundamental Frequency | High average power diode pumped all solid | Pointing stability over temperature (urad/℃) | Polarization | Beam diameter (mm) | Relative humidity | Power supply (110/220VAC) | of short pulse duration, high repetition rate | Cooling method | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FL-355-PS | 355 nm | 1~50 mW | 0.05~2.5 nJ | 20-50 MHz | <10 ps | – | – | <3%, <2%, <1% | TEM00 | ~1.0 | >100:1 Vertical | <15 | 10-35 | PSU-FL-FDA (12V/25A) / PSU-FL-OEM (12V/25A) | >10000 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| FL-355-Pico | 355 nm | 1~50 mW | 10~500 nJ | 0.1-20 MHz | 100-900 ps | – | – | – | – | – | – | <15 | 15-35 | 12V/11.5A | >10000 | <5%, <3% | Pulse duration (ps)2 / 100-900 | <2 | >15 Horizontal (Vertical optional) | 60 | Air cooled | Third harmonic | – | – | – | – | – | – | – | – | Datasheet |
| EO-355-PS | 355 nm | 1~6 W | 1~40 uJ | 1-1000 kHz | <15 ps | – | – | – | – | ≤3 | – | – | 15-30 | – | >10000 | <5% | – | ≤1.5 | – | – | Water cooled | – | Pulse duration (ps) / <15 | <50 | 100:1 | 1.5±0.5 | <60% | PSU-EO-PS | – | – | Datasheet |
| DPS-355-Pico | 355 nm | 100~700 mW | 20-140 nJ | 5 MHz | <50 ps | – | – | – | – | <3 | – | <15 | 15-30 | – | >10000 | <5%, <3% | – | – | – | – | Air cooled | – | – | – | – | – | – | PSU-DPS-Pico | Beam diameter (mm) / ~2 | – | Datasheet |
| PS-D- 532 & 355 -Air | 355 nm | 1~500 mW | 1~500 nJ | 0.1-1 MHz | ~10 ps | – | – | <3%, <2%, <1% | – | – | >100:1 Vertical | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| PS-D-355-Air | 355 nm | 1~1000 mW | 1~100 nJ | 1 kHz-10 MHz | ~10 ps | – | – | <3%, <2%, <1% | – | – | >100:1 Vertical | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| PS-D-355-Water | 355 nm | 1~2000 mW | 1~2000 nJ | 0.4-2 MHz | ~10 ps | – | – | <2%, <1% | TEM00 | <2 | >100:1 Horizontal (Vertical optional) | ≥30 | 20-30 | 36V/40A | >10000 | – | – | <1.2 | – | – | – | – | – | – | – | – | – | – | – | Water cooled | Datasheet |
| PS-D-355 | 355 nm | 1~30 W | 1~30 uJ | 0.4-1 MHz | ~10 ps | – | – | <2%, <1% | TEM00 | <2 | >100:1 Horizontal (Vertical optional) | ≥30 | 20-30 | 36V/40A | >10000 | – | – | <1.2 | – | – | – | – | – | – | – | – | – | – | – | Water cooled | Datasheet |
| PS-D-532 | 355 nm | 1~500 mW | 1~500 nJ | 0.1-1 MHz | ~10 ps | <3%, <2%, <1% | <1.2 | – | – | – | >100:1 Vertical | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
535 NM Green Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours , ±3℃) | Pulse duration (ps) | M2 | Rep. rate | Polarization ratio (dB) | Warm-up time (minutes) | Cooled method | Operating temperature (℃) | Operating voltage (VDC) | Expected lifetime (hours) | Fundamental Frequency | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FL-535-Pico | 535 nm | 1~1000 mW | <5%, <3%, <2% | 100-900 | <1.5 / <2 | 100kHz-20MHz / 100kHz-1MHz | >15 Horizontal (Vertical optional) | <15 | Air cooled | 15-35 | 12V/11.5A | >10000 | Second harmonic | Datasheet |
343nm UV Ultraviolet Laser.
3 models| Model | Wavelength | Output / average power | Power stability (rms, 4 hours , ±3℃) | Pulse duration (ps) | M2 | Rep. rate | Polarization ratio (dB) | Warm-up time (minutes) | Delivery fiber length (cm) | Cooled method | Operating temperature (℃) | Operating voltage (VDC) | Expected lifetime (hours) | Fundamental Frequency | Delivery fiber length(cm) | Pulse duration (ns) | frequency | Rep. rate (MHz) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FL-343-PS | 343 nm | 1~50 mW | <5%, <3% | <10 | <2 | 20-50MHz | >15 Horizontal (Vertical optional) | <15 | 60 | Air cooled | 15-35 | 12V/11.5A | >10000 | Third harmonic | – | – | – | – | Datasheet |
| FL-343-Pico | 343 nm | 1~50 mW | <5%,<3% | 100-900 | <2 | 100kHz-20MHz | >15 Horizontal (Vertical optional) | <15 | – | Air cooled | 15-35 | 12V/11.5A | >10000 | Third harmonic | 60 | – | – | – | Datasheet |
| FL-343-Nano | 343 nm | 10~300 mW | <5%, <3% | – | <2 | – | >15 Horizontal (Vertical optional) | <15 | 60 | Air cooled | 15-35 | 12V/11.5A | >10000 | Third harmonic | – | 0.5-50 | all / fiber / pulsed / laser / at | 0.1-1 | Datasheet |
Infrared Laser, 1030 NM Infrared Laser Module, Infrared DPSS Lasers.
16 models| Model | Wavelength | Output / average power | Single pulse energy (nJ) | Rep. Rate( | Ave power stability (rms, 4 hours±3℃) | Warm-up time (minutes) | Transverse mode | Beam divergence, full angle (mrad) | M2 | Polarization ratio | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | Single pulse energy (uJ) | pulse | Rep. rate | Pulse | Rep. Rate | Rep. rate (MHz) | Beam quality(M2) | Rep. rate (kHz) | Rep. Rate (kHz) | Pulse duration | Pulse duration (fs) | M2 factor | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FL-H-1030-PS | 1030 nm | 1~20 W | 1-500 | 20-120 | <2%, <1% | <10 | TEM00 | <1 | <1.2 | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| PS-FG-1030A | 1030 nm | 1~5 W | – | – | <5%, <3% | <10 | TEM00 | <1.5 | <1.3 | >100:1 Vertical | Water cooled | 10-35 | RAD1PS | >10000 | 1-10 | duration, / high | – | – | – | – | – | – | – | – | – | – | Datasheet |
| PS-FG-1030B | 1030 nm | 5~40 W | – | – | <5%, <3% | <10 | TEM00 | <1.5 | <1.3 | >100:1 Vertical | – | – | RAD1PS | >10000 | 10-80 | duration, / high | – | – | – | – | – | – | – | – | – | – | Datasheet |
| PS-HG-1030A | 1030 nm | 1~5 W | 1-250 | – | <5%, <3% | <10 | TEM00 | <1.5 | <1.3 | >100:1 Vertical | Water cooled | 10-35 | RAD1PS | >10000 | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| PS-HG-1030B | 1030 nm | 5~50 W | – | – | <5%, <3% | <10 | TEM00 | <1.5 | <1.3 | >100:1 Vertical | Water cooled | 10-35 | RAD1PS | – | 1-2.5 | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| FS-H-1030A | 1030 nm | 1~500 mW | – | – | <2%, <1% | <10 | TEM00 | – | <1.2 | >100:1 Vertical | Air cooled | 15-35 | 12V/6.67A | >10000 | – | duration, / high | 80±2 | – | – | – | – | – | – | – | – | – | Datasheet |
| FS-H-1030B | 1030 nm | 500~3000 mW | 6.25-30 | – | <2%, <1% | <10 | TEM00 | – | <1.2 | >100:1 Vertical | Air cooled | 15-35 | RAD1PS | >10000 | – | – | 80±2 | <150 | – | – | – | – | – | – | – | – | Datasheet |
| FS-H-1030C | 1030 nm | 3~20 W | – | – | <2%, <1% | <10 | TEM00 | – | <1.2 | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | <250 | 20-120 | – | – | – | – | – | – | – | Datasheet |
| FS-H-1030D | 1030 nm | 20~50 W | – | – | <2%, <1% | <10 | TEM00 | – | <1.2 | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | duration, / high | 20-120 | – | – | – | – | – | – | – | – | – | Datasheet |
| FS-H-1030E | 1030 nm | 50~100 W | – | – | <2%, <1% | <10 | TEM00 | – | <1.3 | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | duration, / high | 20-120 | – | – | – | – | – | – | – | – | – | Datasheet |
| FS-F-1030A | 1030 nm | 1~10 W | – | – | <2%, <1% | <10 | TEM00 | – | – | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | duration, / high | – | – | – | 1 | <1.3 | – | – | – | – | – | Datasheet |
| FS-F-1030B | 1030 nm | 10~20 W | – | – | <2%, <1% | <10 | TEM00 | – | – | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | <300 | – | – | <1.2 | 100-1000 | – | – | – | – | Datasheet |
| FS-F-1030C | 1030 nm | 20~50 W | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| FS-F-1030D | 1030 nm | 50~100 W | – | – | <2%, <1% | <10 | TEM00 | – | – | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | – | – | – | <1.3 | – | 100-1000 | <300 | – | – | Datasheet |
| FS-G-1030A | 1030 nm | 1~10 W | – | – | – | <10 | TEM00 | – | – | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | – | – | – | – | 50-1000 | – | – | <800 | <1.3 | Datasheet |
| FS-G-1030B | 1030 nm | 10~40 W | – | – | – | <10 | TEM00 | – | – | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | – | – | – | – | 50-1000 | – | <800 | – | <1.3 | Datasheet |
405nm CW Pulse Violet Blue Laser
1 model| Model | Wavelength | Output / average power | Repetition rate | Pulse width | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-405 | 405 nm | 1~100 mW | 0.1~80 MHz | 100~1000 ps | <2%, <1%, <0.5% | Multimode | ~2.5×0.2 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
410nm CW Pulse Violet Blue Laser
1 model| Model | Wavelength | Output / average power | Repetition rate | Pulse width | Power stability (rms, 4 hours ± 3°C) | Transverse mode | M2 | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-410 | 410 nm | 1~100 mW | 0.1~80 MHz | 100~1000 ps | <2%, <1%, <0.5% | Near TEM00 | <1.5 / <1.2 | ~0.5 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | Datasheet |
425 NM Blue Violet Laser, Diode Laser, Blue Laser |
1 model| Model | Wavelength | Output / average power | Transverse mode | Beam divergence, full angle (mrad) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-425 | 425 nm | 1~50 mW | Multimode | <2.5×0.2 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
Femtosecond Laser |
27 models| Model | Wavelength | Output / average power | Repetition rate | Single pulse energy (nJ) | Fiber | pulse | Warm-up time (minutes) | Transverse mode | M2 factor | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | Pulse duration (fs) | Ave power stability (rms, 4 hours±3℃) | Polarization ratio | Single pulse energy (uJ) | pulse duration, | M2 | Frequency doubler | Pulse | Beam quality(M2) | Pulse duration | All Fiber Femtosecond pulsed laser at 1064nm | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FS-H- 515A | 515 nm | 1-100 mW | 80±1 MHz | 1-1.25 | Femtosecond / pulsed / laser / at | Ave power stability (rms, 4 hours±3℃) / <2%, <1% | <10 | TEM00 | <1.2 | Air cooled | 10-35 | 12V/6.67A | >10000 | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| FS-H- 515B | 515 nm | 100-1000 mW | 80±1 MHz | – | – | – | <10 | TEM00 | <1.2 | Air cooled | 10-35 | RAD1PS | >10000 | <150 | <2%, <1% | >100:1 Horizontal | – | – | – | – | – | – | – | – | Datasheet |
| FS-H- 515C | 515 nm | 1-10 W | 80±1 MHz | – | Femtosecond / pulsed / laser / at | – | <10 | TEM00 | <1.2 | Water cooled | 10-35 | RAD1PS | >10000 | <250 | <2%, <1% | >100:1 Horizontal | – | – | – | – | – | – | – | – | Datasheet |
| FS-H- 515D | 515 nm | 10-30 W | 80±1 MHz | – | Femtosecond / pulsed / laser / at | – | <10 | TEM00 | <1.2 | Water cooled | 10-35 | RAD1PS | >10000 | <250 | <2%, <1% | >100:1 Horizontal | – | – | – | – | – | – | – | – | Datasheet |
| FS-H- 515E | 515 nm | 30-60 W | 80±1 MHz | – | Femtosecond / pulsed / laser / at | – | <10 | TEM00 | <1.3 | Water cooled | 10-35 | RAD1PS | >10000 | <250 | <2%, <1% | >100:1 Horizontal | – | – | – | – | – | – | – | – | Datasheet |
| FS-F- 515A | 515 nm | 1-2 W | 1 MHz | – | Femtosecond / pulsed / laser / at | Ave power stability (rms, 4 hours±3℃) / <2%, <1% | <10 | TEM00 | <1.3 | Water cooled | 10-35 | RAD1PS | >10000 | – | – | – | 1-2 | – | – | – | – | – | – | – | Datasheet |
| FS-F- 515B | 515 nm | 2-8 W | 100 kHz-1 MHz | – | Femtosecond / pulsed / laser / at | – | <10 | TEM00 | <1.2 | Water cooled | 10-35 | RAD1PS | >10000 | <300 | <2%, <1% | >100:1 Horizontal | – | – | – | – | – | – | – | – | Datasheet |
| FS-F- 515C | 515 nm | 8-20 W | 100 kHz-1 MHz | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | |
| FS-F- 515D | 515 nm | 20-40 W | 100 kHz-1 MHz | – | Femtosecond / pulsed / laser / at | – | <10 | TEM00 | <1.3 | Water cooled | 10-35 | RAD1PS | >10000 | <300 | <2%, <1% | >100:1 Horizontal | – | – | – | – | – | – | – | – | Datasheet |
| FS-G- 515A | 515 nm | 1-20 W | 50 kHz-1 MHz | – | – | – | <10 | TEM00 | – | Water cooled | 15-35 | RAD1PS | >10000 | <500 | <2%, <1% | >100:1 Horizontal | – | high repetition | <1.3 | – | – | – | – | – | Datasheet |
| FS-H- 5 32A | 532 nm | 1-100 mW | 80±1 MHz | 1-1.25 | Femtosecond / pulsed / laser / at | Ave power stability (rms, 4 hours±3℃) / <2%, <1% | <10 | TEM00 | – | Air cooled | 10-35 | 12V/6.67A | >10000 | – | – | >100:1 Horizontal | – | – | <1.2 | – | – | – | – | – | Datasheet |
| FS-H- 5 32B | 532 nm | 100-2000 mW | 80±1 MHz | – | – | – | <10 | TEM00 | – | Air cooled | 10-35 | RAD1PS | >10000 | <150 | <2%, <1% | >100:1 Horizontal | – | – | <1.2 | – | – | – | – | – | Datasheet |
| FS-H-780A | 780 nm | 1-50 mW | 80±2 MHz | 0.1-0.6 | – | duration, / high | <10 | TEM00 | <1.2 | Air cooled | 10-35 | 12V/6.67A | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | – | LASER HEAD (780) / POWER SUPPLY | – | – | – | – | Datasheet |
| FS-H- 1030A | 1030 nm | 1-500 mW | 80±2 MHz | – | – | duration, / high | <10 | TEM00 | – | Air cooled | 15-35 | 12V/6.67A | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | <1.2 | – | – | – | – | – | Datasheet |
| FS-H- 1030B | 1030 nm | 500-3000 mW | 80±2 MHz | 6.25-30 | – | – | <10 | TEM00 | – | Air cooled | 15-35 | RAD1PS | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | <1.2 | – | <150 | – | – | – | Datasheet |
| FS-H- 1030C | 1030 nm | 3-20 W | 80±2 MHz | – | – | – | <10 | TEM00 | – | Water cooled | 15-35 | RAD1PS | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | <1.2 | – | <250 | – | – | – | Datasheet |
| FS-H- 1030D | 1030 nm | 20-50 W | 80±2 MHz | – | – | duration, / high | <10 | TEM00 | – | Water cooled | 15-35 | RAD1PS | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | <1.2 | – | – | – | – | – | Datasheet |
| FS-H- 1030E | 1030 nm | 50-100 W | 80±2 MHz | – | – | duration, / high | <10 | TEM00 | – | Water cooled | 15-35 | RAD1PS | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | <1.3 | – | – | – | – | – | Datasheet |
| FS-F- 1030A | 1030 nm | 1-10 W | 1 MHz | – | – | duration, / high | <10 | TEM00 | – | Water cooled | 15-35 | RAD1PS | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | – | – | – | <1.3 | – | – | Datasheet |
| FS-F- 1030B | 1030 nm | 10-20 W | 1 MHz | – | – | – | <10 | TEM00 | – | Water cooled | 15-35 | RAD1PS | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | – | – | <300 | <1.2 | – | – | Datasheet |
| FS-F- 1030C | 1030 nm | 20-50 W | 1 MHz | – | – | – | <10 | TEM00 | – | Water cooled | 15-35 | RAD1PS | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | – | – | <300 | <1.2 | – | – | Datasheet |
| FS-F- 1030D | 1030 nm | 50-100 W | 1 MHz | – | – | – | <10 | TEM00 | – | Water cooled | 15-35 | RAD1PS | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | – | – | – | <1.3 | <300 | – | Datasheet |
| FS-G- 1030A | 1030 nm | 1-10 W | 50 kHz-1 MHz | – | – | – | <10 | TEM00 | <1.3 | Water cooled | 15-35 | RAD1PS | >10000 | <800 | – | >100:1 Vertical | – | – | – | – | – | – | – | – | Datasheet |
| FS-G- 1030B | 1030 nm | 10-40 W | 50 kHz-1 MHz | – | – | – | <10 | TEM00 | <1.3 | Water cooled | 15-35 | RAD1PS | >10000 | – | – | >100:1 Vertical | – | – | – | – | – | – | <800 | – | Datasheet |
| FS-H- 10 64A | 1064 nm | 1-500 mW | 80±2 MHz | 1-6.25 | – | duration, / high | <10 | TEM00 | <1.2 | Air cooled | 10-35 | 12V/6.67A | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | – | – | – | – | – | Pulse duration (fs) / <150 | Datasheet |
| FS-H- 10 64B | 1064 nm | 500-5000 mW | 80±2 MHz | 6.25-62.5 | – | duration, / high | <10 | TEM00 | <1.2 | Air cooled | 10-35 | RAD1PS | >10000 | – | <2%, <1% | >100:1 Vertical | – | – | – | – | – | – | – | – | Datasheet |
| FS-H- 1560A | 1560 nm | 1-200 mW | 80±2 MHz | 1-2.5 | – | – | <10 | TEM00 | <1.2 | Air cooled | 10-35 | 12V/6.67A | >10000 | <50 | – | >100:1 after PM fiber | – | – | – | – | – | – | – | – | Datasheet |
1560nm DFB Laser, Infrared Laser, DPSS Laser |
2 models| Model | Wavelength | Output / average power | Single pulse energy (nJ) | Rep. rate (MHz) | Pulse duration (fs) | Warm-up time (minutes) | Transverse mode | M2 factor | Polarization ratio | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FS-H-1560A | 1560 nm | 1~200 mW | 1-2.5 | 80±2 | <50 | <10 | TEM00 | <1.2 | >100:1 after PM fiber | Air cooled | 10-35 | 12V/6.67A | >10000 | Datasheet |
| FC-OEM-1560 | 1560 nm | 1~15 mW | – | – | – | – | – | – | – | – | – | – | – |
2910 NM MID Infrared Laser, Solid State Laser, IR Laser |
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours±3℃) | Beam divergence, full angle (mrad) | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|
| MIL-PS-2910 | 2910 nm | 1~2000 mW | <5%, <3% | <11 | Air Cooled | 15-35 | RAD1PS | >10000 | Datasheet |
3.2 ΜM Infrared Laser, CW Laser, Solid State Laser |
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours±3℃) | Beam divergence, full angle (mrad) | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|
| MIL-PS-3205 | 3200 nm | 1~2000 mW | <5%, <3% | <11 | Air Cooled | 15-35 | RAD1PS | >10000 | Datasheet |
3440 NM MID Infrared Laser, Solid State Laser, IR Laser |
1 model| Model | Wavelength | Output / average power | Ave power stability (rms, 4 hours±3℃) | Warm-up time (minutes) | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|
| MIL-PS-3440 | 3440 nm | 1~1000 mW | <3%, <2%, <1% | <10 | Waterr cooled | 15-30 | RAD1PS | >10000 | Datasheet |
3640 NM MID Infrared Laser, Solid State Laser, IR Laser |
1 model| Model | Wavelength | Output / average power | Ave power stability (rms, 4 hours±3℃) | Warm-up time (minutes) | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|
| MIL-PS-3640 | 3640 nm | 1~1000 mW | <3%, <2%, <1% | <10 | Waterr cooled | 15-30 | RAD1PS | >10000 | Datasheet |
3967 NM MID Infrared Laser, Solid State Laser, IR Laser |
1 model| Model | Wavelength | Output / average power | Ave power stability (rms, 4 hours±3℃) | Warm-up time (minutes) | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|
| MIL-PS-3967 | 3967 nm | 1~600 mW | <3%, <2%, <1% | <10 | Waterr cooled | 15-30 | RAD1PS | >10000 | Datasheet |
4235 NM MID Infrared Laser, Solid State Laser, IR Laser |
1 model| Model | Wavelength | Output / average power | Ave power stability (rms, 4 hours±3℃) | Warm-up time (minutes) | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|
| MIL-PS-4235 | 4235 nm | 1~60 mW | <3%, <2%, <1% | <10 | Waterr cooled | 15-30 | RAD1PS | >10000 | Datasheet |
4 ΜM MID Infrared Laser, Solid State Laser |
1 model| Model | Wavelength | Output / average power | |
|---|---|---|---|
| MIL-PS-4000 | 4000 nm | 1~600 mW | Datasheet |
620 NM RED Diode Laser.
2 models| Model | Wavelength | Output / average power | All picosecond pulsed laser | Pulse duration(ps) | Max average power (mW) | Rep. rate (kHz)(optional) | Ave power stability (over 4 hours) | Warm-up time (minutes) | Operating temperature (°C) | |
|---|---|---|---|---|---|---|---|---|---|---|
| PS-L-620 | 620 nm | 1~100 mW | is made features of short pulse duration, high repetition rate and good beam | <500 | 1~100 | 3 | <5%, <3% | <10 | 20~30 | Datasheet |
| PS-M-620 | 620 nm | 1~500 mW | – | – | – | – | – | – | – | Datasheet |
637 NM RED Diode Laser |
1 model| Model | Wavelength | Output / average power | |
|---|---|---|---|
| Picosecond Pulsed | 637 nm | 1-50 mW |
280nm Q Switched UV Laser.
2 models| Model | Wavelength | Output / average power | All picosecond pulsed laser | Pulse duration(ps) | Max average power (mW) | Rep. rate (kHz)(optional) | Ave power stability (over 4 hours) | Warm-up time (minutes) | Operating temperature (°C) | Rep. rate (kHz) | Power stability (rms, over 4 hours) | Beam diameter at the aperture (1/e2,mm) | Cooled method | Operating temperature (℃) | Power supply (220/110VAC) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| PS-L-280 | 280 nm | 1~10 mW | is made features of short pulse duration, high repetition rate and good beam | <500 | 1~10 | 3 | <5%, <3% | <10 | 20~30 | – | – | – | – | – | – | Datasheet |
| PS-M-280 | 280 nm | 1~40 mW | – | – | – | – | – | – | – | 500-1000 | <3%, (<2% optional) | ~3.0 | Water cooled | 15~35 | On request | Datasheet |
295nm Q Switched UV Laser.
2 models| Model | Wavelength | Output / average power | All picosecond pulsed laser | Pulse duration(ps) | Max average power (mW) | Rep. rate (kHz)(optional) | Ave power stability (over 4 hours) | Warm-up time (minutes) | Operating temperature (°C) | Rep. rate (kHz) | Power stability (rms, over 4 hours) | Beam diameter at the aperture (1/e2,mm) | Cooled method | Operating temperature (℃) | Power supply (220/110VAC) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| PS-L-295 | 295 nm | 1~10 mW | is made features of short pulse duration, high repetition rate and good beam | <500 | 1~10 | 3 | <5%, <3% | <10 | 20~30 | – | – | – | – | – | – | Datasheet |
| PS-M-295 | 295 nm | 1~50 mW | – | – | – | – | – | – | – | 500-1000 | <3%, (<2% optional) | ~3.0 | Water cooled | 15~35 | On request | Datasheet |
310nm Q Switched UV Laser.
2 models| Model | Wavelength | Output / average power | All picosecond pulsed laser | Pulse duration(ps) | Max average power (mW) | Rep. rate (kHz)(optional) | Ave power stability (over 4 hours) | Warm-up time (minutes) | Operating temperature (°C) | Rep. rate (kHz) | Power stability (rms, over 4 hours) | Beam diameter at the aperture (1/e2,mm) | Cooled method | Operating temperature (℃) | Power supply (220/110VAC) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| PS-L-310 | 310 nm | 1~10 mW | is made features of short pulse duration, high repetition rate and good beam | <500 | 1~10 | 3 | <5%, <3% | <10 | 20~30 | – | – | – | – | – | – | Datasheet |
| PS-M-310 | 310 nm | 1~40 mW | – | – | – | – | – | – | – | 500-1000 | <3%, (<2% optional) | ~3.0 | Water cooled | 15~35 | On request | Datasheet |
330nm UV Laser.
2 models| Model | Wavelength | Output / average power | All picosecond pulsed laser | Pulse duration(ps) | Max average power (mW) | Rep. rate (kHz)(optional) | Ave power stability (over 4 hours) | Warm-up time (minutes) | Operating temperature (°C) | Rep. rate (kHz) | Power stability (rms, over 4 hours) | Beam diameter at the aperture (1/e2,mm) | Cooled method | Operating temperature (℃) | Power supply (220/110VAC) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| PS-L-330 | 330 nm | 1~10 mW | is made features of short pulse duration, high repetition rate and good beam | <500 | 1~10 | 3 | <5%, <3% | <10 | 20~30 | – | – | – | – | – | – | Datasheet |
| PS-M-330 | 330 nm | 1~30 mW | – | – | – | – | – | – | – | 500-1000 | <3%, (<2% optional) | ~3.0 | Water cooled | 15~35 | On request | Datasheet |
560nm Q Switched Yellow Green Laser.
2 models| Model | Wavelength | Output / average power | All picosecond pulsed laser | Pulse duration(ps) | Max average power (mW) | Rep. rate (kHz)(optional) | Ave power stability (over 4 hours) | Warm-up time (minutes) | Operating temperature (°C) | |
|---|---|---|---|---|---|---|---|---|---|---|
| PS-L-560 | 560 nm | 1~100 mW | is made features of short pulse duration, high repetition rate and good beam | <500 | 1~100 | 3 | <5%, <3% | <10 | 20~30 | Datasheet |
| PS-M-560 | 560 nm | 1~800 mW | – | – | – | – | – | – | – | Datasheet |
395 NM UV Diode Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Pulse width (ps) | Transverse mode | Rep. | repetition | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Operating voltage (VDC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-395 | 395 nm | 1~50 mW | <3%, <2%, <1% | 200-1000 | Near TEM00 | 100kHz-20MHz | rate / 100kHz / to / 20MHz, | <0.5 | <5 | Air cooled | 10-35 | 12V/3.34A | >10000 | Datasheet |
420nm Violet Blue Laser, Diode Laser, Violet Laser |
1 model| Model | Wavelength | Output / average power | Transverse mode | Beam divergence, full angle (mrad) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-420 | 420 nm | 1~50 mW | Multimode | <2.5×0.2 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
590nm Q Switched Yellow Green Laser.
2 models| Model | Wavelength | Output / average power | All picosecond pulsed laser | Pulse duration(ps) | Max average power (mW) | Rep. rate (kHz)(optional) | Ave power stability (over 4 hours) | Warm-up time (minutes) | Operating temperature (°C) | |
|---|---|---|---|---|---|---|---|---|---|---|
| PS-L-590 | 590 nm | 1~100 mW | is made features of short pulse duration, high repetition rate and good beam | <500 | 1~100 | 3 | <5%, <3% | <10 | 20~30 | Datasheet |
| PS-M-590 | 590 nm | 1~600 mW | – | – | – | – | – | – | – | Datasheet |
High Energy Laser |
5 models| Model | Wavelength | Pulse energy | Repetition rate | Pulse width | Power stability (rms, 4 hours , ±3℃) | M2 | Pointing stability over temperature (urad/℃) | Polarization | Beam diameter (mm) | Beam divergence, full angle (mrad) | Cooled method | Warm-up time (minutes) | Operating temperature (℃) | Relative humidity | Power supply (110/220VAC) | Expected lifetime (hours) | Energy stability (std dev/mean) | Expected lifetime (pulses) | Energy stability | Power supply(110/220VAC) | Expected lifetime( pulses) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| EO-532-PS | 532 nm | 1-60 uJ | 1-1000 kHz | <15 ps | <5%, <3% | ≤1.4 | <50 | 100:1 | 1.5±0.5 | ≤2 | Water cooled | <15 | 15-30 | <60% | PSU-EO-PS | >10000 | – | – | – | – | – | Datasheet |
| DPS-532-P-Subnano | 532 nm | 1-15 mJ | 1-100 Hz | <500 ps | – | – | – | – | – | <3 | Water cooled | <15 | 15-30 | – | PSU-DPS-Subnano | – | <5%, <3% | 109 | – | – | – | Datasheet |
| LPS-532-Subnano | 532 nm | 15-100 mJ | 1-10 Hz | <500 ps | – | – | – | – | ~7 | <3 | Water cooled | <15 | 15-30 | – | PSU-LPS-Subnano | – | – | 107-108 | – | – | – | Datasheet |
| DPS-1064-P-Subnano | 1064 nm | 1-30 mJ | 1-100 Hz fixed | <500 ps | – | <2 | – | – | – | <3 | Water cooled | <15 | 15-30 | – | PSU-DPS-Subnano | – | <5%, <3%, <2% | 109 | – | – | – | Datasheet |
| LPS-1064-Subnano | 1064 nm | 30-200 mJ | 1-10 Hz | <500 ps | – | – | – | – | ~7 | <3 | Water cooled | <15 | 15-30 | – | – | – | – | – | <5%, <3%, <2% | PSU-LPS-Subnano | 107-108 | Datasheet |
High Power Laser |
1 model| Model | Wavelength | Output / average power | Repetition rate | Pulse width | Macro-Pulse duration (us) | Macro-Rep. rate | Micro-Pulse duration (ns) | Power stability (rms) | Warm-up time (minutes) | Cooled method | Operating temperature (℃) | Power supply (110/220VAC) | Expected lifetime (pulses) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| LGS-589.159-PS | 589.159 nm | 1-25 W | 100±1 MHz | Macro <160 us Micro <1 ns | <160 | 500Hz | <1 | <5%, <3% | <15 | Water cooled | 15-35 | PSU-LGS-PS | 109 | Datasheet |
Infrared Diode Laser AT 3800 NM.
1 model| Model | Wavelength | Output / average power | |
|---|---|---|---|
| MIL-PS-3810 | 3800 nm | 1~600 mW | Datasheet |
Infrared Laser, 905 NM Infrared Diode Pulse Lasers, High Power Diode Laser System.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-905 | 905 nm | 1~30 mW | <2%, <1%, <0.5% | Near TEM00 | <1.0 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | Datasheet |
Infrared Laser, 915 NM Infrared Diode Lasers, High Power Diode Laser System.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-915 | 915 nm | 1~30 mW | <2%, <1%, <0.5% | Multimode | <3.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
780 NM Infrared Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-780 | 780 nm | 1~50 mW | <2%, <1%, <0.5% | Multimode | <3.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
976 NM Infrared Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-976 | 976 nm | 1~50 mW | <2%, <1%, <0.5% | Multimode | <3.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
642 NM RED Laser, RED Diode Laser, RED Laser Module |
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | M2 | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-642 | 642 nm | 1~50 mW | <2%, <1%, <0.5% | <1.5 / <1.2 | <1.0 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | Datasheet |
213nm UV Ultraviolet Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms) | Pulse width (ps) | Jitter (ns, sdev) | Beam divergence, full angle (mrad) | Beam diameter (mm) | Rep. rate | Cooled method | Warm-up time (minutes) | Operating temperature (℃) | Power supply (110/220VAC) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DPS-213-Pico | 213 nm | 1~30 mW | <5%, <3% | <50 | <1ns | <3 | ~2 | 5MHz | Air cooled | <15 | 15-30 | PSU-DPS-Pico | Datasheet |
375 NM UV Diode Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-375 | 375 nm | 1~50 mW | <2%, <1%, <0.5% | Multimode | ~2.5×1.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
400 NM Blue Violet Diode Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-400 | 400 nm | 1~100 mW | <2%, <1%, <0.5% | Multimode | ~2.5×0.2 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
445 NM Blue Violet Diode Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | M2 | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-445 | 445 nm | 1~60 mW | <2%, <1%, <0.5% | <1.5 / <1.2 | <1 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | Datasheet |
447 NM Blue Violet Diode Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | M2 | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-447 | 447 nm | 1~60 mW | <2%, <1%, <0.5% | <1.5 / <1.2 | <1 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | Datasheet |
450 NM Blue Violet Diode Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | M2 | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-450 | 450 nm | 1~60 mW | <2%, <1%, <0.5% | <1.5 / <1.2 | <1 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | Datasheet |
515 NM Green Laser.
12 models| Model | Wavelength | Output / average power | Single pulse energy (uJ) | Rep. rate (kHz) | Pulse duration (ps) | Ave power stability (rms, 4 hours±3℃) | Warm-up time (minutes) | Transverse mode | Beam divergence, full angle (mrad) | M2 | Polarization ratio | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | Rep. rate (MHz) | features of short pulse duration, high repetition | Single pulse energy (nJ) | Fiber | pulse | M2 factor | Pulse duration (fs) | pulse duration, | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| PS-FG-515A | 515 nm | 1-20 W | 1-40 | 500-1000 | 10±1 | <5%, <3% | <10 | TEM00 | <1.5 | <1.3 | >100:1 Horizontal | Water cooled | 10-35 | RAD1PS | >10000 | – | – | – | – | – | – | – | – | Datasheet |
| PS-HG-515A | 515 nm | 1-20 W | 0.05-1 | – | 10-150 | – | <10 | TEM00 | <1.5 | <1.3 | >100:1 Horizontal | Water cooled | 10-35 | RAD1PS | >10000 | 20-120 | Ave power stability (rms, 4 hours±3℃) / <5%, <3% | – | – | – | – | – | – | Datasheet |
| FS-H-515A | 515 nm | 1~100 mW | – | – | – | – | <10 | TEM00 | – | – | – | Air cooled | 10-35 | 12V/6.67A | >10000 | 80±1 | – | 1-1.25 | Femtosecond / pulsed / laser / at | Ave power stability (rms, 4 hours±3℃) / <2%, <1% | <1.2 | – | – | Datasheet |
| FS-H-515B | 515 nm | 100~1000 mW | – | – | – | <2%, <1% | <10 | TEM00 | – | – | >100:1 Horizontal | Air cooled | 10-35 | RAD1PS | >10000 | 80±1 | – | – | – | – | <1.2 | <150 | – | Datasheet |
| FS-H-515C | 515 nm | 1~10 W | – | – | – | <2%, <1% | <10 | TEM00 | – | – | >100:1 Horizontal | Water cooled | 10-35 | RAD1PS | >10000 | 20-120 | – | – | Femtosecond / pulsed / laser / at | – | <1.2 | <250 | – | Datasheet |
| FS-H-515D | 515 nm | 10~30 W | – | – | – | <2%, <1% | <10 | TEM00 | – | – | >100:1 Horizontal | Water cooled | 10-35 | RAD1PS | >10000 | 20-120 | – | – | Femtosecond / pulsed / laser / at | – | <1.2 | <250 | – | Datasheet |
| FS-H-515E | 515 nm | 30~60 W | – | – | – | <2%, <1% | <10 | TEM00 | – | – | >100:1 Horizontal | Water cooled | 10-35 | RAD1PS | >10000 | 20-120 | – | – | Femtosecond / pulsed / laser / at | – | <1.3 | <250 | – | Datasheet |
| FS-F-515A | 515 nm | 1~2 W | 1-2 | – | – | – | <10 | TEM00 | – | – | – | Water cooled | 10-35 | RAD1PS | >10000 | 1 | – | – | Femtosecond / pulsed / laser / at | Ave power stability (rms, 4 hours±3℃) / <2%, <1% | <1.3 | – | – | Datasheet |
| FS-F-515B | 515 nm | 2~8 W | – | – | – | <2%, <1% | <10 | TEM00 | – | – | >100:1 Horizontal | Water cooled | 10-35 | RAD1PS | >10000 | – | – | – | Femtosecond / pulsed / laser / at | – | <1.2 | <300 | – | Datasheet |
| FS-F-515C | 515 nm | 8~20 W | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| FS-F-515D | 515 nm | 20~40 W | – | 100-1000 | – | <2%, <1% | <10 | TEM00 | – | – | >100:1 Horizontal | Water cooled | 10-35 | RAD1PS | >10000 | – | – | – | Femtosecond / pulsed / laser / at | – | <1.3 | <300 | – | Datasheet |
| FS-G-515A | 515 nm | 1~20 W | – | 50-1000 | – | <2%, <1% | <10 | TEM00 | – | <1.3 | >100:1 Horizontal | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | – | – | – | <500 | high repetition | Datasheet |
520 NM Green Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-520 | 520 nm | 1~30 mW | <2%, <1%, <0.5% | Multimode | ~4.0×0.5 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
Infrared Laser,1060 NM Infrared Diode Lasers,infrared Diode Laser System.
2 models| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-1060 | 1060 nm | 1~30 mW | <2%, <1%, <0.5% | Multimode | <3.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
| MDL-PS-1064 | 1064 nm | 1~30 mW | <2%, <1%, <0.5% | Multimode | <3.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
Infrared Laser,785 NM Infrared Diode Lasers,infrared Diode Laser System.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-785 | 785 nm | 1~50 mW | <2%, <1%, <0.5% | Multimode | <3.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
Infrared Diode Laser, 808 NM Infrared Diode Lasers, High Power Diode Laser System.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-808 | 808 nm | 1~60 mW | <2%, <1%, <0.5% | Multimode | <3.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
Infrared Laser, 852 NM Infrared Diode Lasers.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | M2 | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-852 | 852 nm | 1~30 mW | <2%, <1%, <0.5% | <1.5 | <1.0 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | Datasheet |
Infrared Laser, 940 NM Infrared Diode Lasers, High Power Diode Laser System.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-940 | 940 nm | 1~60 mW | <2%, <1%, <0.5% | Multimode | <3.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
Infrared Laser, 975 NM Infrared Diode Lasers, High Power Diode Laser System.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | Transverse mode | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-975 | 975 nm | 1~50 mW | <2%, <1%, <0.5% | Multimode | <3.0 | <5 | Air cooled | 10-35 | PSU-H-FDA/PSU-H-LED | >10000 | Datasheet |
RED Laser, 633 NM RED Laser, HE NE Laser |
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | M2 | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-633 | 633 nm | 1~50 mW | <2%, <1%, <0.5% | <1.5 / <1.2 | <1.0 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | Datasheet |
640 NM RED Diode Laser.
1 model| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | M2 | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-640 | 640 nm | 1~50 mW | <2%, <1%, <0.5% | <1.5 / <1.2 | <1.0 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | Datasheet |
655 NM RED Diode Laser.
8 models| Model | Wavelength | Output / average power | Power stability (rms, 4 hours ± 3°C) | M2 | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Cooled method | Operating temperature (°C) | Power supply (100-240VAC) | Expected lifetime (hours) | Transverse mode | Operating voltage(external PCB1) | Connection | Operating temperature | Storage temperature | Humidity | Beam divergence (mrad) | Laser operation mode | Modulation optional | Storage temperature (°C) | Humidity (%) | Weight (g) | Operating voltage(internal PCB) | Dimensions of internal PCB | Power stability(rms, over 4 hours) | Warm-up time | Operating voltage(PSU-II-OEM) | Dimensions of laser head | Warranty (years) | Operating voltage(PSU-V-OEM) | Operating voltage(PSU-I-OEM) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| MDL-PS-655 | 655 nm | 1~50 mW | <2%, <1%, <0.5% | <1.5 / <1.2 | <1.0 | <5 | Conduction | 10-35 | PSU-III-FDA/PSU-III-LED/PSU-A-D/PSU-III-OEM | >10000 | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| PGL-D8-655 | 655 nm | 1~50 mW | – | – | <1 | – | – | – | – | 10000 | Near TEM00 | 3VDC | Cable with flying leads | 0°C to 40°C | -20°C to 80°C | < 90%, non-condensing | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| PGL-D12-655 | 655 nm | 1~100 mW | – | – | <1 | – | – | – | – | 10000 | Near TEM00 | 3VDC | Cable with flying leads | 0°C to 40°C | -20°C to 80°C | < 90%, non-condensing | – | – | – | – | – | – | – | – | – | – | – | – | – | – | – | Datasheet |
| PGL-LF-655 | 655 nm | 1~130 mW | – | – | – | – | – | -10°C to +45°C | – | – | – | – | Cable with flying leads | – | – | – | <1.5 | CW | TTL 30kHz or analog (0-3V or 0-5V) | -20°C to +80°C | < 90 %, non-condensing | 45g | – | – | – | – | – | – | – | – | – | Datasheet |
| PGL-VI-655 | 655 nm | 1~150 mW | – | – | <1 | – | – | – | – | 10000 | Near TEM00 | – | Cable with flying leads | 0°C to 40°C | -20°C to 80°C | < 90 %, non-condensing | – | – | – | – | – | – | 3VDC | mm2 / Φ12×50 | – | – | – | – | – | – | – | Datasheet |
| PGL-FS-655 | 655 nm | 1~150 mW | – | – | <1 | – | – | – | – | 10000 | Near TEM00 | – | Cable with flying leads | -10°C to 50°C | -20°C to 80°C | < 90%, non-condensing | – | – | – | – | – | – | – | – | <5%, <3%, <1% | minutes / <10 | 5V / (TTL30kHz or Analog 0-5V,optional) | 77(L)×30(W)×30(H)mm3 | – | – | – | Datasheet |
| PGL-H-655 | 655 nm | 1~800 mW | – | – | <1 | – | – | – | – | 10000 | Near TEM00 | – | Cable with flying leads | -10°C to 50°C | -20°C to 80°C | < 90%, non-condensing | – | – | – | – | – | – | – | – | <5%, <3%, <1% | minutes / <10 | 5V / (TTL30kHz or Analog 0-5V,optional) | 77(L)×30(W)×30(H)mm3 | – | – | – | Datasheet |
| PGL-V-H-655 | 655 nm | 1~1000 mW | – | – | <1.5 / <3.5 | – | – | – | – | 10000 | Near TEM00 / Multimode | – | 9 pin connector | -10°C to 50°C | -20°C to 80°C | < 90%, non-condensing | – | – | – | – | – | – | – | – | <5%, <3%, <1% | minutes / <10 | – | 92(L)×40(W)×40(H)mm3 | 1 | 100-240VAC | 12VDC | Datasheet |
Laboratory Instrument |
1 model| Model | Wavelength | |
|---|---|---|
| Laser Technology Experiment | — |
Supercontinuum Source
3 models| Model | Wavelength | Output / average power | Repetition rate | Pulse width | Power stability | M² | |
|---|---|---|---|---|---|---|---|
| FL-SC-OEM (1~200 mW) | 470~2400 nm | 1~200 mW | 2 MHz | ~350 ps | <2% | <1.1 | |
| FL-SC-OEM (200~350 mW) | 470~2400 nm | 200~350 mW | 4 MHz | ~350 ps | <1% | <1.1 | |
| FL-SC-OEM (350~500 mW) | 470~2400 nm | 350~500 mW | 50kHz~200kHz, 1 MHz | ~350 ps | <1% | <1.1 |
THE Manufacturer Q Switched 1064nm Laser
2 models| Model | Wavelength | Output / average power | Pulse energy | Repetition rate | Pulse width | Power stability | M² | Beam diameter (mm) | Cooled method | Operating temperature (℃) | Power supply (110/220VAC) | Expected lifetime (hours) | Pointing stability over temperature (urad/℃) | Polarization | Beam divergence, full angle (mrad) | Warm-up time (minutes) | Relative humidity | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DPS-1064-Pico | 1064 nm | 5-30 W @1 MHz | 5-30 uJ @1 MHz | 100 kHz-10 MHz (adjustable) | <50 ps 50-1000(adjustable) | <3%, <2%, <1% | <1.5 | ~2 | Air cooled (DPS-1064-Pico-I); Water cooled (DPS-1064-Pico-II) | 15-30 | PSU-DPS-Pico | >10000 | – | – | – | – | – | Datasheet |
| EO-1064-PS | 1064 nm | 5-20 W @1 MHz | 1-150 uJ | 1-100 Hz | <15 ps | <5%, <3% | ≤1.3 | 1.5±0.5 | Water cooled | 15-30 | PSU-EO-PS | >10000 | <50 | 100:1 | ≤2 | <15 | <60% | Datasheet |
Mode Locked & Picosecond Laser |
1 model| Model | Wavelength | Output / average power | Repetition rate | Power stability | M² | Single pulse energy (mJ) | Pulse duration (ps) | Energy stability (std dev/mean) | Beam divergence, full angle (mrad) | M2 | Warm-up time (minutes) | Cooled method | Operating temperature (℃) | Power supply (110/220VAC) | Expected lifetime (pulses) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DPS-1064-PS | 1064 nm | 5-20 W | 0-1000 kHz | <3%, <5% | ≤1.3 | 1-30 | <500 | <5%, <3%, <2% | <3 | <2 | <15 | Water cooled | 15-30 | PSU-DPS-Subnano | 109 | Datasheet |
THE Manufacturer High Energy Q Switched Laser
1 model| Model | Wavelength | Output / average power | Pulse energy | Repetition rate | Pulse width | Power stability | M² | of short pulse duration, high repetition rate | Cooled method | Operating temperature (℃) | Power supply (110/220VAC) | Expected lifetime (hours) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DPS-532-Pico | 532 nm | 2-10 W @10 MHz | 0.2-1 uJ @10 MHz | 0.1-10 MHz | <50 ps | <3%, <2%, <1% | <1.5 | Beam diameter (mm) / ~2 | Air cooled (DPS-532-Pico-I); Water cooled (DPS-532-Pico-II) | 15-30 | PSU-DPS-Pico | >10000 | Datasheet |
Picosecond Fiber Laser |
10 models| Model | Wavelength | Output / average power | Repetition rate | Pulse width | Power stability | M² | stability, | Fiber connector | Fiber length (m) | Fiber jacket | Beam diameter (mm) | Polarization ratio (dB) | Warm-up time (minutes) | Cooled method | Operating temperature (℃) | Operating voltage (VDC/VAC) | Expected lifetime (hours) | fiber | M2 | Operating voltage (VDC) | Delivery fiber length (cm) | Fundamental Frequency | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FL-1064-Pico | 1064 nm | 10-5000 mW | 0.1-20 MHz | 100-900 ps | <3%, <2% | <1.2 | M2 / <1.2 / <1.8 | FC/APC, Collimator optional | 1 | PVC, Metal optional | 4±1 (Collimator output) | Random / >15 | <15 | Air cooled | 15-35 | 12V/11.5A | >10000 | – | – | – | – | – | Datasheet |
| FL-1064-PS | 1064 nm | 1-2000 mW | 20-60 MHz | <10 ps | <3%, <2%, <1%, <0.5% | <1.2 | – | – | – | – | – | Random / > 15 | <15 | Air cooled | 15-35 | – | >10000 | pulsed / laser / at | <1.2 / <1.5 | 12V/11.5A | – | – | Datasheet |
| FL-1064-PS-Seed | 1064 nm | 0.5-1 mW | 20-60 MHz | <10 ps | <3%, <2%, <1% | <1.2 | – | FC/APC | 1 | PVC, Metal optional | – | Random / > 15 | <15 | – | 15-35 | – | >10000 | – | – | 12V/11.5A | – | – | Datasheet |
| FL-1070-Pico | 1070 nm | 10-5000 mW | 0.1-20 MHz | 100-900 ps | <3%, <2% | <1.2 | – | FC/APC, Collimator optional | 1 | PVC, Metal optional | 4±1 (Collimator output) | Random / >15 | <15 | Air cooled | 15-35 | 12V/11.5A | >10000 | – | <1.2 / <1.8 | – | – | – | Datasheet |
| FL-1080-Pico | 1080 nm | 10-5000 mW | 0.1-20 MHz | 100-900 ps | <3%, <2% | <1.2 | M2 / <1.2 / <1.8 | FC/APC, Collimator optional | 1 | PVC, Metal optional | 4±1 (Collimator output) | Random / >15 | <15 | Air cooled | 15-35 | 12V/11.5A | >10000 | – | – | – | – | – | Datasheet |
| FL-1550-Pico | 1550 nm | 100-1000 mW | 0.1-20 MHz | 100-900 ps | <3%, <2% | <1.2 | Rep. rate3 / 100kHz-20MHz | FC/APC, Collimator optional | 1 | PVC, Metal optional | 4±1 (Collimator output) | Random / > 15 | <15 | Air cooled | 15-35 | 12V/11.5A | >10000 | – | – | – | – | – | Datasheet |
| FL-1550-PS | 1550 nm | 1-2000 mW | 20-60 MHz | <10 ps | <3%, <2%, <1%, <0.5% | <1.2 | – | – | – | – | – | Random / > 15 | <15 | Air cooled | 15-35 | – | >10000 | pulsed / laser / at | <1.2 / <1.5 | 12V/11.5A | – | – | Datasheet |
| FL-532-Pico | 532 nm | 1-1000 mW | 0.1-20 MHz | 100-900 ps | <5%, <3%, <2% | <1.5 | – | – | – | – | – | >15 Horizontal (Vertical optional) | – | Air cooled | 15-35 | – | >10000 | – | <1.5 / <2 | 12V/11.5A | 60 | Second harmonic | Datasheet |
| FL-532-PS | 532 nm | 1-150 mW | 20-60 MHz | <10 ps | <3%, <2% | <1.5 | – | – | – | – | – | >15 Horizontal (Vertical optional) | – | Air cooled | 15-35 | – | >10000 | – | – | 12V/11.5A | 60 | – | Datasheet |
| FL-775-Pico | 775 nm | 50-200 mW | 0.1-20 MHz | 100-900 ps | <5%, <3% | <1.5 | – | – | – | – | – | >15 Horizontal (Vertical optional) | – | Air cooled | 15-35 | – | >10000 | – | – | 12V/11.5A | – | Second harmonic | Datasheet |
Picosecond Diode Laser |
11 models| Model | Wavelength | Output / average power | Repetition rate | Power stability | M² | Single pulse energy (nJ) | Warm-up time (minutes) | Transverse mode | Beam divergence, full angle (mrad) | Polarization ratio | Cooled method | Operating temperature (℃) | Power supply (100-240VAC) | Expected lifetime (hours) | Pulse duration (ps) | Pulse width (ps) | Operating temperature (°C) | Operating voltage (VDC) | Single pulse energy (mJ) | pulse | Pulse duration | Cooling method | M2 | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| FL-H-1064-PS | 1064 nm | 1-20 W | 20-120 MHz (Fixed) | <2%, <1% | <1.2 | 1-500 | <10 | TEM00 | <1 | >100:1 Vertical | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | – | – | – | – | – | – | Datasheet |
| FL-H-532-PS | 532 nm | 1-5000 mW | 20-120 MHz (Fixed) | <2%, <1% | <1.2 | – | <10 | TEM00 | – | >100:1 Horizontal | Air cooled | 15-35 | 12V/6.67A | >10000 | <8ps; or one fixed value between 10 ps-150 ps | – | – | – | – | – | – | – | – | Datasheet |
| MDL-PS-488 | 488 nm | 1~50 mW | 0.1~20 MHz | <3%, <2%, <1% | – | – | <5 | Near TEM00 | ~1.0 | – | Air cooled | – | – | >10000 | – | 100-1000 | 10-35 | 12V/3.34A | – | – | – | – | – | Datasheet |
| MDL-PS-635 | 635 nm | 1~50 mW | 0.1~80 MHz | <3%, <2%, <1% | – | – | <5 | Near TEM00 | ~1.0 | – | Air cooled | 10-35 | – | >10000 | – | 100-1000 | – | 12V/3.34A | – | – | – | – | – | Datasheet |
| MDL-PS-637 | 637 nm | 1~50 mW | 0.1~80 MHz | <3%, <2%, <1% | – | – | <5 | Near TEM00 | ~1.0 | – | Air cooled | 10-35 | – | >10000 | – | 100-1000 | – | 12V/3.34A | – | – | – | – | – | Datasheet |
| MDL-PS-660 | 660 nm | 1~50 mW | 0.1~20 MHz | <3%, <2%, <1% | – | – | <5 | Near TEM00 | ~1.0 | – | Air cooled | – | – | >10000 | – | 100-1000 | 10-35 | 12V/3.34A | – | – | – | – | – | Datasheet |
| MIL-PS-2910-4235 | 2910 nm | 1-2000 mW | 15 MHz | <3%, <2%, <1% | – | – | <10 | – | – | – | Waterr cooled | 15-30 | RAD1PS | >10000 | – | – | – | – | – | – | – | – | – | Datasheet |
| PS-A-1064 | 1064 nm | 1 W/ 2.5 W | 1 kHz | <5%, <3% | <1.2 | – | – | – | <1.5 | – | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | – | 0.1-1 / 1-2.5 | duration, / high | – | – | – | Datasheet |
| PS-A-532 | 532 nm | 1 W | 1 kHz | <5%, <3% | <1.2 | – | – | – | <1.5 | – | Water cooled | 15-35 | RAD1PS | >10000 | – | – | – | – | 0.1-1 | duration, / high | – | – | – | Datasheet |
| PS-D-1064 | 1064 nm | 1-100 W | 400 kHz~120 MHz | <2%, <1% | <1.2 | – | ≥30 | TEM00 | <3 | >100:1 Horizontal (Vertical optional) | – | 20-30 | – | >10000 | – | – | – | 36V/40A | – | – | ~10 | Water cooled | – | Datasheet |
| PS-D-532-Water | 532 nm | 1-2000 mW | 80 MHz±1 | <3%, <2%, <1% | – | – | ≥30 | TEM00 | <2 | >100:1 Horizontal (Vertical optional) | – | 20-30 | – | – | ~10 | – | – | 36V/40A | – | – | – | Water cooled | <1.2 | Datasheet |
660 NM RED Laser.
2 models266nm UV Ultraviolet Laser.
1 model| Model | Wavelength | Output / average power | |
|---|---|---|---|
| PS-R-266 | 266 nm | 1~50 mW |
Not sure which model fits?
Send the physics — wavelength, mode, power or energy, linewidth or pulse width, delivery, control and safety — and we qualify the source.
