Laboratory optical integration
Laser Viewing Card: The component is selected by matching its interfaces and error contribution to the complete instrument budget.
| Wavelength Range | 250nm-450nm | |
|---|---|---|
| Model Number | LDC-250-40 | |
| Active Area | 40×40 mm | |
| Coating Material | Down-conversion fluorescent materials | |
| Sensitivity @ 450 nm | 0.26 uW/ cm 2 | Dark environment |
| 0.36 mW/ cm 2 | Fluorescent lamp |
| Wavelength Range | 700nm–1600 nm | |
|---|---|---|
| Model Number | LDC-1550-25 | LDC-1550-40 |
| Active Area | 25×25 mm | 40×40 mm |
| Coating Material | Up-conversion fluorescent materials | |
| Sen sitivity @ 980 nm | 0.85 uW/ cm 2 | Dark environment |
| Sensitivity @ 1550 nm | 5.7 uW/ cm 2 | |
| Sensitivity @ 980 nm | 3.82 uW/ cm 2 | Fluorescent lamp |
| Sensitivity @ 1550 nm | 65 uW/ cm 2 |
| Wavelength Range | 2um-13um |
|---|---|
| Model Number | LDC-13000-40 |
| Active Area | 40×40 mm |
| Coating Material | Temperature sensitive film |
| Sensitivity Temperature | 30 ℃ |
| Wavelength Range | 9 00–1100nm |
|---|---|
| Model Number | LDC-1100A |
| Peak Emission | 540-548 nm/651-666 nm |
| Active Area | 20×15 mm |
| Sensitivity @ 1064 nm | >20 mW/ cm 2 |
| CW Damage Threshold (kW/cm 2 ) | 10 |
| Base Plate | Precision ceramic material |
| Application | 1.YAG/ fiber laser adjustment 2. IR laser and LED beam test |
| Dimension(mm) | 1 5×50 |
Application context
Why this design is used
Application fit depends on the ordered configuration; catalog values are separated from fields that still require confirmation.
Research instrument development
Laser Viewing Card: A documented configuration prevents optical, mechanical and control assumptions from becoming integration failures.
Engineering reference
Specify Laser Viewing Card from the interfaces inward
Laser Viewing Card is a configurable configurable scientific component in the Laser components and accessories family. The final part number should be released only after the optical, mechanical, electrical and environmental fields below are matched to the intended instrument.
This component must be qualified inside the complete optical, mechanical and electrical chain. Interfaces, performance limits and environmental conditions are coupled; a model name alone is not sufficient to release an instrument design.
Selection guidance describes the engineering fields that must be checked. It does not assign an option-dependent value that is absent from the catalog record.
Configuration fields to confirm
- Primary function
- State the required optical or mechanical result and the measurement tolerance.
- Operating range
- Define wavelength, motion, frequency or other applicable working range.
- Performance budget
- Set allowable loss, noise, drift, error and safety margin.
- Physical interface
- Confirm dimensions, aperture, connector, thread, hole pattern and datum surfaces.
- Control interface
- Specify supply, command, feedback, trigger and communications requirements.
- Environment
- State temperature, vacuum, humidity, contamination and duty-cycle conditions.
Qualification sequence
- 1Define the measurement objective and the performance limit that Laser Viewing Card must satisfy.
- 2Freeze wavelength, mechanical, fiber and electrical interfaces before selecting option codes.
- 3Check loss, noise, heat, motion or vibration contributions in the complete system budget.
- 4Confirm the final drawing, pinout, environmental suffix and acceptance test with the quotation.
Technical FAQ
Configuration questions for Laser Viewing Card
What must be specified before ordering Laser Viewing Card?
Confirm primary function, operating range, performance budget, physical interface, control interface, and environment. These fields are coupled, so the final part number should be checked against the complete instrument rather than selected from the model name alone.
How should Laser Viewing Card be integrated into the system?
This component must be qualified inside the complete optical, mechanical and electrical chain. Interfaces, performance limits and environmental conditions are coupled; a model name alone is not sufficient to release an instrument design. Freeze the optical, mechanical and electrical interfaces before releasing the surrounding assembly.
Which documentation should be approved for Laser Viewing Card?
Approve the configuration-specific specification, mechanical drawing, connector or pinout definition, environmental suffix and acceptance-test limits supplied with the quotation. Any field absent from the local record remains a confirmation item, not an assumed capability.