Optical Switches
LightBend™ 1x4 High Power Optical Switch
The LB 1×4 Series fiber optic switch connects optical channels by redirecting an incoming optical signal into a selected output fiber. This is achieved by using our patent pending opto-mechanical configuration activated via an electrical control signal. Latching operation preserves the selected optical path after the drive signal has been removed. The switch has integrated electrical position sensors, and our new material based advanced design significantly reduces moving part position sensitivity, offering unprecedented high stability as well as an unmatched low cost. Electronic driver is available for this series of switches.
Configuration options
Build & quote
Configure the options below and add your exact build to the enquiry — we confirm the part number and availability.
We confirm the exact part number for your configuration on enquiry.
Prefix: LBHP · Type: 1x2 · Wavelength: 1060 · Switch: Latching · Power: 5W · Fiber Type: SMF-28 · Fiber Cover: Bare Fiber · Fiber Length: 0.25m · Connector: None
Downloads
Datasheets & documents
System integration
Integration and compatibility
Use these checks to connect LightBend™ 1x4 High Power Optical Switch to the surrounding optical, mechanical and control system. Every value shown is taken from this model's own specification record.
- Optical interface and fiber
- Fiber Type: SMF-28, MM 50/125, MM 62.5/125, PM1550, PM1310, PM980, PM850, Special · Fiber Cover: Bare Fiber, 900um Tube, Special
- Specify connector polish and fiber architecture together. FC/PC, FC/APC and SMA interfaces, and single-mode, multimode and polarization-maintaining fibers, impose different return-loss, mode-field and alignment requirements.
- Wavelength and loss budget
- Wavelength: 1060, 1310, 1550, 780, 850, 980, Special
- Check the Optical Switches passband, insertion loss, return loss and power handling at the actual source wavelength; a nominal telecom-band label is not a substitute for the configured range.
Technical FAQ
Integration questions for LightBend™ 1x4 High Power Optical Switch
Which fiber and connector does the LightBend™ 1x4 High Power Optical Switch use?
Fiber Type: SMF-28, MM 50/125, MM 62.5/125, PM1550, PM1310, PM980, PM850, Special · Fiber Cover: Bare Fiber, 900um Tube, Special. Specify connector polish and fiber architecture together. FC/PC, FC/APC and SMA interfaces, and single-mode, multimode and polarization-maintaining fibers, impose different return-loss, mode-field and alignment requirements.
How should the LightBend™ 1x4 High Power Optical Switch be included in an optical power budget?
Wavelength: 1060, 1310, 1550, 780, 850, 980, Special. Check the Optical Switches passband, insertion loss, return loss and power handling at the actual source wavelength; a nominal telecom-band label is not a substitute for the configured range.
Need this configured?
Share your wavelength, fiber type, connector, power handling and control requirements and we will qualify the matching configuration and part number.
Model selection
Nearby series comparison
Compare LightBend™ 1x4 High Power Optical Switch with the closest available models in the Optical Switches family.
| Selection parameter | LightBend™ 1x4 High Power Optical Switch (current) | LightBend™ 1x1, 1x2, 2x2 Bypass SM Optical Switch |
|---|---|---|
| Wavelength range | 1060, 1310, 1550, 780, 850, 980, Special | 1260-1620, 1060, C+L, 1310, 1410, 1550, 650, 780, 850, 1310 & 1550 |
| Fiber type | SMF-28, MM 50/125, MM 62.5/125, PM1550, PM1310, PM980, PM850, Special | SM28, Corning XB, Draka BBE |
| Connector / control | None, FC/APC, Special | None, FC/PC, FC/APC, LC/PC, Special |
